Factory Suspension on Hotrods and Muscle Cars generally through 1957 all have the same suspension configuration. Mostly Coilsprings on the front, and leafsprings
on the rear. 1958 to 1982 mostly have coils on all 4 corners. So one prices fits all. Specific brackets are available for most GM cars, while others use a
Generic Bracket that must be modified to suit your vehicle. Even specific brackets must be modified to suit your needs. First determine your everyday ride-height
which will be your personal setting. To go lower, the brackets must be shorter, but keep in mind, your factory Geometry will start to be stressed at anything over 3".
This means you will have to have shorter control arms to compensate for balljoint angles and to be able to align. You cannot go a Lower Ride Height, but you
can slam it at the drive-in. If you have factory Leafsprings, you must install a 4Link. PRICING: There are those of you that will be diehard and insist that the more
you pay, the more you get, but I am here to dispell that idea, at least in Air Suspension. Our Competitor charges over twice the amount that we do, and we give
you higher engineered product and always use the Largest Compressors, no toys like the Thomas or Viar that take forever to pump up your airtank. So take your
time, compare each component and I will show you the way as we go.
Read: The Knowledge Base for more information |
 |
You start with our Basic Kit, which is not so basic at all. This is everything you need, but not maybe everything you want. So we offer an array of option UPGRADES to build your kit any way you want by adding Pre-Set Ride Controllers, Stainless Steel Chromed tanks, 2"Taller De Nominator-II bags, Air-Engine Manifold Pre-wired, Pre-plumbed Valving Systems, and Plug & Play. Kit as shown
$1241
|
HotRods_PAGE |
|
Visit a Competitor, compare, then come back, save big $$$ with us. We are a manufacturer selling direct to you, with no middle men to take a bite. You can choose any brackets for $1241 kit below.

55-57 Chev Front . .58-64 Chev Rear . . 48-54 Chev Front . . Mustang Front . . 52-74 Ford/Merc Front . . . . . . . . . . . . . . . . . . .
"Click Here" for complete Bracket Selection! |
UPGRADE OPTIONS SHOWN BELOW
|
AIR SPRINGS/AIR BAGS The bags that come with the kit are the same specification as Ridetech's
Air bags, but you can UPGRADE them to any of the bags at the right
for $20 each. The most IMPORTANT thing you can do is MAKE ROOM
for the largest diameter bag possible.The larger the bag, the less psi it
takes to lift, so if you are engineering for a smooth ride, do not use a
baby bag. De-Nominator-II's are 2" taller than Ridetechs bags. |

Click on bags to find out the specs and diameters
Any bag $20 Upgrade Each
Order must be phoned for UPGRADE PRICING!
|
SPRING POCKET ELIMINATORS You use supplied bucket to trim spring pocket with a
plasma cutter to allow you to slide it into place and weld. Your frame actually will be several
times stronger than factory and you will not have to use any upper barrels, and you can adjust the height level before final welding. Buckets are mandatory on all big blocks,
or anything that requires more than 120psi to lift. Also, by eliminating the upper barrels you
can drop deeper than ever before. If you run #2500 bags on the front of a big block, it will rise
very slow, if even at all. |

Allows use of 8.5" bag/pair $99
|
SPINDLES Prices reduced to $129/pair for
any size Mustang,
Chevrolet, MoPar spindles
in stock.
|
Hot Rod & Muscle Car Spindles
$129
pair |
|
|
AIRBAG CONTROL ARMS All of our control arms are manufactured using state
of the art CNC cutting, bending and forming processes with high strength steel
plate and DOM Steel Tubing. We manufacture our ball joint mounts out of steel
plate ranging from 0.375" to 0.500" thick and some control arms are made using
CNC Turned steel ball joint cups. All of our tubular control arms are made using
1.0" dia. - 1.75" dia. x 0.120" - 0.188" wall DOM Steel Tubing that is precision bent,
coped and Mig/Tig welded by the best welders in the industry |
|
PLUG & PLAY is completely assembled. Absolutely no wiring to do except connect
gauge wires. All plumbing,wiring is done for you. Comes with 100% dutycycle
DC7500, and SPEED controls. If you have a mechanic install the Plug and
Play, you will save over 16hours of install time, or aproximately $800 on your install.
Just install bags, and run airlines. Your done... A Weather cover is available for $25.
PLUG & PLAY and DeNominator-II bags are the two best UPGRADES you can
buy. Air-Engine uses the same dependable Brass Valves plumbed into a Manifold
Distribution Center with 100% compression fittings. |
$300 Upgrade to $995 Kit $300
Order must be phoned for UPGRADE PRICING! |
SMART-RIDE IS COMPLETELY
WIRED/PROGRAMMED FOR YOU
5 Pre-sets. One touch ride height, one button takes you back to
programmed ride height, when you fire up, Adjust each wheel individually,
Pancake up/down, Sensor Transducers, Auto Leak Detection, Advanced
"Teach" technology, One wire to dash does it all. $650
UPGRADE for Plug & Play and SMARTRIDE. We will install and program
it to your Plug & Play, or to your separately purchased Air-Engine
|
$650 Upgrade to $995 Kit $650
Order must be phoned for UPGRADE PRICING! |
UPGRADE Liteduty weld-on . . . . . . .$199
UPGRADE Hvyduty weld-on . . . . . . $259
UPGRADE Parallel weld-on. . . . . . . .$399
UPGRADE Bolt-On Differential . . . . $399
All come with 4" C-Sections Standard
UPGRADE to 5-pc Bridge Notch . .. . ..$75 |

Order must be phoned for UPGRADE PRICING! |
Stainless Steel Chromed UPGRADE tanks
UPGRADE from the standard black 3- Gallon tank to a non-rusting Stainless.
UPGADE to 3-Gallon Stainless . . . . .$25
UPGRADE to 5-Gallon Stainless . . . $55 |

Order must be phoned for UPGRADE PRICING! |
UPGRADE Shock Relocater Kit with brackets
If your factory shocks are installed in the middle of your coilsprings, then you will need a shock relocater kit, or you simply are relocating your existing shocks.
$98 UPGRADE to $895 kit. . . . . . . .$98
$118 UPGRADE to Chrome . . . . .. $118 |
|
ALL KINDS OF OTHER STUFF! |
USE CAUTION:AIRSHOCKS are not for everyone. They look good and have that neat HotRod look, but travel is limited to the travel of the shock, which is 3".
So... if you want to go low, you should get bags & brackets that allow you up to 10" or more of travel. AIRSHOCKS are not returnable, so be sure, and also be sure to measure twice.
Beginning March 1st, 2010, we will be offering the World's first Airshock without "O" Rings. You will never have to worry about tearing a seal or leaks around the seals. |

Non-Adjustable . . . . $499 pr
Adjustable . . . . . . . . $599 pr |
|

Vintage Billet Grilles for Impalas, Graham & Muscle Cars |

Forged CNC Custom
Billet Steering Wheel
$399 |

Digital readouts only, 5 readouts, including Air Tank.
|

Full FBSS Digital Controler with four(4)
3-Position Switches that return to center. 5 Readouts, including Airtank. |

Air Horns for Hot Rods, Trucks and Motorcycles
Largest selection, Lowest Prices
Preview the Sound. |

Lambo Doors . . . . . . . $369
Hinges & Hydraulic Struts
Electronic Actuators not included |

ACTUATORS . . . . $69 pr |
Be very careful when using Actuators to lift a Lambo Door. While the door might not exceed 150lbs, the extended weight may be more than the actuator can handle, for this reason, there is no warranty because of potential misuse.
2" . . 8" . . 10" . . 12"
Raise hood, open trunk, lambo doors or whatever you dream up.
1-9 |
10-24 |
25-49 |
|
$69 |
$55 |
$52 |
$41 |
|
|

BILLET ACCESSORIES
Gas Caps, Shift Knobs, Window Cranks, Extinguishers and more. |

STEEL BRAKE LINES $49
The brake lines should be replaced in any vehicle that is raised or lowered. Our steel braided hose can be custom fitted to any vehicle. |

SPRING BAR STOOLS. . $139
Full size bar stools and chairs made from spring steel. Ad a custom look to any bar with your choice of colors. |
|
|
|
Standard Suicide Hinges
This is the complete kit including BearClaw latches, install kit, Complete suicide door hinge system, and Automatic door safety actuators.
Others sell this kit for over $500 |
$139
1-2 $139
3-4 $111
5-9 $104
10-24 $90
25+ $83 |
  |
Large Suicide Hinges
CNC Billet 3 3/4" tall, 4" deep, 5/8" wall. Adjustable steel base plate & mounts,
Bear Claw latch kit, strikers,
Safety Actuators. Others sell this kit
for over $1,000
Hinges Brushed.......................$299
Hinges/Latches/Actuators......$369
Complete Kit Polished............$429
|
$319
1-2 $319
3-4 $255
5-9 $239
10-24 $207
25+ $191
Brushed Hinges ONLY
|
|
GULLWING DOOR KIT
The Gullwing Door Kit is
currently one of the hottest trends in the automotive
re-styling world. This hinge eliminates the factory door hinges and replaces them with a new hinge that allows the doors to swing up parallel with the ground. |
|
$149
1-2 $149
3-4 $119
5-9 $112
10-24 $97
25+ $89 |
|
|
|